BIS insights

BIS withdraws 38 Indian Standards from October 5, 2026

The Bureau of Indian Standards issued Ref: HQ-PUB017/1/2020-PUB-BIS (1629) on October 7, 2026. BIS notification 1629 withdraws 38 Indian Standards from October 5, 2026, among them gas cylinder filling ratios, AC stabilized power supplies and inverters. It is issued under Rule 15(1), Bureau of Indian Standards Rules, 2018.

BIS · October 7, 2026

Vishnu Gupta

The Bureau of Indian Standards (BIS), Department of Consumer Affairs, issued notification Ref: HQ-PUB017/1/2020-PUB-BIS (1629) at New Delhi on October 7, 2026. It appeared in the Gazette of India, Extraordinary, Part III, Section 4, No. 655, dated November 4, 2026. BIS made it under rule 15(1) of the Bureau of Indian Standards Rules, 2018.

The schedule lists 38 Indian Standards that "have been cancelled and stands withdrawn" from October 5, 2026, two days before the notification's own date. They include two parts of IS 1885 (electrotechnical vocabulary), five parts of IS 9080 on safety in electro-heat installations, seven parts of IS 11182 on evaluating insulation systems of electrical equipment, both parts of IS 11260 on stabilized power supplies with AC output, IS 13032 on AC miniature circuit-breaker boards up to 1 000 V and IS 13314 on solid state inverters run from storage batteries.

Others include IS 3710 on filling ratios for low pressure liquefiable gases in cylinders, IS 8775 on filling pressures for permanent gases in cylinders, IS 8596, IS 9330, IS 9332 and IS 13619 on steam, hot water and waste heat boilers, IS 6296 on short link chain for lifting appliances, two parts of IS 7012 on X-ray tube shields, IS 14153 on photovoltaic power generating systems and IS/ISO 21573 (Part 2) : 2020 on concrete pumps. The oldest is IS 2464 – 1963, on built-up mica for electrical purposes.

The notification names no standard that replaces any of the 38, and gives no reason for withdrawing them. None of the 38 is the standard of a Quality Control Order in IndusDesk's QCO tracker, and none is a standard of BIS's Compulsory Registration Scheme for electronics. The notification doesn't say whether any other rule or regulation cites them. S. K. Verma, Scientist F & DDG (Hallmarking), signed it.

Issued by
Bureau of Indian Standards, Department of Consumer Affairs
Document
Notification Ref: HQ-PUB017/1/2020-PUB-BIS (1629)
Dated
October 7, 2026
Published
Gazette of India, Extraordinary, Part III, Section 4, No. 655, November 4, 2026 (CG-DL-E-07112026-277765)
Standards withdrawn
38
Withdrawn from
October 5, 2026
Replacements named
None
Withdrawn standards named in QCOs or the CRS
None, in IndusDesk's QCO tracker and CRS list
Legal basis
Rule 15(1), Bureau of Indian Standards Rules, 2018
Signed by
S. K. Verma, Scientist F & DDG (Hallmarking)

Indian Standards withdrawn from October 5, 2026

Sl NoIndian Standard withdrawnTitle
1IS 1885 (Part 80) : 1994 (IEC Pub 50 (301) (1983))Electrotechnical Vocabulary Part 80 General Terms on Measurements in Electricity
2IS 1885 (Part 81) : 1993 (IEC Pub 50 (302) (1983))Electrotechnical Vocabulary Part 81 Electrical Measuring Instruments
3IS 2032 (Part XXV) – 1980Graphical Symbols Used in Electrotechnology Part XXV Electrical Installations in Ships
4IS 2464 – 1963Specification for Built-Up Mica for Electrical Purposes
5IS 3710 – 1978Filling Ratios for Low Pressure Liquefiable Gases Contained in Cylinders (First Revision)
6IS 6296 – 1983Specification for Short Link Chain Grade S(6) Calibrated for Pulley Blocks and other Lifting Appliances (First Revision)
7IS 7012 (Part 2) – 1985Specification for X-Ray Tube Shield Part 2 Type Shx 2
8IS 7012 (Part 3) – 1985Specification for X-Ray Tube Shield Part 3 Type Shx 3
9IS 8504 (Part 3) : 1994Guide for Determination of Thermal Endurance Properties of Electrical Insulating Materials Part 3 Statistical Methods
10IS 8596 – 1977Recommended Parameters of Stationary Steam Boilers
11IS 8775 – 1978Filling Pressure and Corresponding Developed Pressure for Permanent Gases Contained in Cylinders
12IS 8992 – 1978Test Methods for Induction Furnaces with Submerged Channels
13IS 9050 – 1979Nominal Dimensions of Cylindrical Machined Graphite Electrodes with Threaded Sockets and Connecting Pins for use in Electric ARC Furnaces
14IS 9080 (Part II/Sec I) – 1979Safety Requirements in Electro-Heat Installations Part II Particular Requirements for Resistance Heating Equipment Section 1 Protection in Direct Resistance Heating Installations
15IS 9080 (Part II/Sec 2) – 1980Safety Requirements in Electro-Heat Installations Part II Particular Requirements for Resistance Heating Equipment Section 2 Protection in Indirect Resistance Heating Installations
16IS 9080 (Part II/Sec 3) – 1981Safety Requirements in Electro-Heat Installations Part II Particular Requirements for Resistance Heating Equipment Section 3 Protection in Potassium and Sodium Nitrate and Nitrite Bath Furnaces
17IS 9080 (Part II/Sec 4) – 1981Safety Requirements in Electro-Heat Installations Part II Particular Requirements for Resistance Heating Equipment Section 4 Protection in Installations used for Drying Varnishes and other Similar Products
18IS 9080 (Part IV) – 1981Safety Requirements in Electro-Heat Installations Part IV Particular Requirements for ARC Furnace Installations
19IS 9330 – 1979Terminology for Parameters of Waste Heat Boilers and Boilers for Special Purposes
20IS 9332 – 1979Recommended Parameters of Waste Heat Boilers and Boilers for Special Purposes
21IS 10122 – 1982Methods of Tests for Crucible Induction Furnaces
22IS 11174 – 1984Specification for Aromatic Polyimide Paper Covered Rectangular and Square Copper Wires with Temperature Index 200
23IS 11182 (Part 1) – 1984Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 1 Identification, Evaluation and Ageing Mechanisms
24IS 11182 (Part 2) – 1984Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 2 Thermal Endurance Test Procedures
25IS 11182 (Part 3/Sec 1) – 1986Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 3 Electrical Endurance Test Procedures Section 1 General Considerations and Evaluation Procedures Based on Normal Distributions
26IS 11182 (Part 3/Sec 2) : 1996Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 3 Electrical Endurance Test Procedures Section 2 Evaluation Procedures Based on Extreme-Value Distributions
27IS 11182 (Part 5) : 1993 (IEC Pub 941 (1988))Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 5 Mechanical Endurance Functional Tests
28IS 11182 (Part 6) – 1986Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 6 Performance Evaluation Based on Service Experience and Functional Tests
29IS 11182 (Part 7/Sec 1) – 1986Guide for the Evaluation of Insulation Systems of Electrical Equipment Part 7 Multi-Factor Functional Testing Section 1 Test Procedures
30IS 11260 (Part 1) – 1985Specification for Stabilized Power Supplies, AC Output Part 1 Rating and Performance
31IS 11260 (Part 2) – 1985Specification for Stabilized Power Supplies, AC Output Part 2 Tests
32IS 12188 – 1987Specification for Electric Direct Arc Melting Furnaces
33IS 12434 – 1988Specification for Coating/Plating Thickness Tester, Destructive Type
34IS 13032 : 1991AC Miniature Circuit-Breaker Boards for Voltages Not Exceeding 1 000 V, Specification
35IS 13314 : 1992Solid State Inverters Run from Storage Batteries, Specification
36IS 13619 : 1993Industrial Steam and Hot Water Boiler Plants, Maintaining of Log and Summary Sheets, Recommendations
37IS 14153 : 1994Guide for General Description of Photovoltaic (PV) Power Generating System
38IS/ISO 21573 (Part 2) : 2020Building Construction Machinery and Equipment, Concrete Pumps Part 2 Procedure for Examination of Technical Parameters (First Revision)

The notification (PDF, 768 KB)

Source: Gazette of India, CG-DL-E-07112026-277765.

Checked against the official copy on November 7, 2026.