QCO tracker

Quality Control Order for cross recessed, drilling, tapping, drywall and wood screws

Cross recessed screws need the BIS Standard Mark from November 1, 2025, but a 2026 amendment pauses enforcement for drywall, chipboard and wood screws. The Bureau of Indian Standards is the certifying and enforcing authority. Certification is under Scheme-I of Schedule-II to the Bureau of Indian Standards (Conformity Assessment) Regulations, 2018.

Cross Recessed Screws (Quality Control) Order, 2025 · Ministry of Commerce and Industry (Department for Promotion of Industry and Internal Trade)

IndusDesk ·

The Cross Recessed Screws (Quality Control) Order, 2024 was issued by the Ministry of Commerce and Industry (Department for Promotion of Industry and Internal Trade) as S.O. 4099(E), dated September 17, 2024, under section 16 of the Bureau of Indian Standards Act, 2016, and published September 20, 2024. It covers fourteen standards: cross recessed and hexagon washer head drilling screws (IS 18471 Parts 1 to 3, IS 18476), cross recessed tapping screws (IS 18480 Parts 1 to 3), type H or type Z cross recess screws (IS 7483, IS 7485 Parts 1 and 2, IS 7486), drywall screws (IS 18507 : 2024), chipboard screws (IS 18508 : 2024) and cross-recessed countersunk head wood screws (IS 18509 : 2023).

The screws must conform to the corresponding Indian Standard and bear the Standard Mark under a licence from the Bureau of Indian Standards, as per Scheme-I of Schedule-II to the Bureau of Indian Standards (Conformity Assessment) Regulations, 2018. Exclusions cover goods made domestically for export, imports forming part of a finished good, sub-assembly or component, imports for making export products, goods made by Udyam-registered enterprises within set investment and turnover limits, and limited imports for research and development. The Bureau enforces the order; contraventions are punishable under the Bureau of Indian Standards Act, 2016.

S.O. 3927(E), dated August 27, 2025, superseded the 2024 order with the Cross Recessed Screws (Quality Control) Order, 2025. It kept the same standards and exemptions, marked entries 1 to 4 as revised as 18471: 2025, and set November 1, 2025 for enterprises in general, February 1, 2026 for small enterprises and May 1, 2026 for micro enterprises.

On June 20, 2026 the Ministry of Steel issued S.O. 3298(E), the Cross Recessed Screws (Quality Control) Amendment Order, 2026, under which enforcement of the drywall, chipboard and wood screw entries is not operative for 3 years from publication in the gazette. The 2025 order is listed as in force.

Order
Cross Recessed Screws (Quality Control) Order, 2025
Issued by
Ministry of Commerce and Industry (Department for Promotion of Industry and Internal Trade)
Product group
Cross Recessed Screws
Where it stands
Amended
What it requires
The screws in the Table must conform to the corresponding Indian Standard and bear the Standard Mark under a licence from the Bureau of Indian Standards as per Scheme-I of Schedule-II to the Bureau of Indian Standards (Conformity Assessment) Regulations, 2018.
Certification scheme
Scheme-I of Schedule-II to the Bureau of Indian Standards (Conformity Assessment) Regulations, 2018
Came into force
The Cross Recessed Screws (Quality Control) Order, 2025 came into force on the date of its publication in the Official Gazette (August 27, 2025), with November 1, 2025 as the date of implementation in general in its Table. The 2024 order it superseded came into force on its publication (September 20, 2024), with six months from publication as the date of implementation in general.
Small enterprises
Under the 2025 order, February 1, 2026 for small enterprises and May 1, 2026 for micro enterprises, as defined under the Micro, Small and Medium Enterprises Development Act, 2006; the 2024 order had given nine and twelve months from publication. Both orders also exclude goods manufactured domestically by an enterprise registered under the Udyam portal with investment in plant and machinery or equipment not exceeding twenty-five lakh rupees and turnover not exceeding two crore rupees for the previous financial year, as certified by a Chartered Accountant.
Exemptions
  • Goods or articles manufactured domestically for export
  • Goods or articles imported as a part of any finished good or sub-assembly or component
  • Goods or articles imported by domestic manufacturer for manufacturing products for export
  • Goods or articles manufactured domestically by an enterprise registered under the Udyam portal of the Ministry of Micro, Small and Medium Enterprises, with investment in plant and machinery or equipment at original cost not exceeding twenty-five lakh rupees and turnover not exceeding two crore rupees for the previous financial year, as certified by a Chartered Accountant
  • Goods or articles imported up to two hundred kilograms per year for the purpose of research and development by manufacturers of cross recessed screws, which are not to be sold commercially and can be disposed of as scrap, with a financial year-wise record maintained and furnished if so desired by Government authorities
  • Under S.O. 3298(E), enforcement of the entries at serial numbers 12, 13 and 14 (IS 18507 : 2024, IS 18508 : 2024 and IS 18509 : 2023) is not operative for a period of 3 years from date of publication in the gazette (S.O. 3298(E) was published June 22, 2026)
Enforcement
The Bureau of Indian Standards is the certifying and enforcing authority. Any person who contravenes the order is punishable under the provisions of the Bureau of Indian Standards Act, 2016.

The products and their standards

ProductIndian StandardTitle of the standard
Cross Recessed ScrewsIS 18471 (Part 1) : 2023/ ISO 15481:1999 (revised as 18471: 2025, per S.O. 3927(E))Fasteners - Cross Recessed Drilling Screws with Tapping Screw Thread Part 1 Pan Head
Cross Recessed ScrewsIS 18471 (Part 2) :2023/ ISO 15482:1999 (revised as 18471: 2025, per S.O. 3927(E))Fasteners - Cross Recessed Drilling Screws with Tapping Screw Thread Part 2 Countersunk Head
Cross Recessed ScrewsIS 18471 (Part 3) :2023/ ISO 15483:1999 (revised as 18471: 2025, per S.O. 3927(E))Fasteners - Cross Recessed Drilling Screws with Tapping Screw Thread Part 3 Raised Countersunk Head
Cross Recessed ScrewsIS 18476 : 2023/ ISO 15480:2019 (revised as 18471: 2025, per S.O. 3927(E))Fasteners - Hexagon Washer Head Drilling Screws with Tapping Screw Thread
Cross Recessed ScrewsIS 18480 (Part 1) :2023/ ISO 7049 : 2011Cross Recessed Tapping Screws: Part 1 Pan Head
Cross Recessed ScrewsIS 18480 (Part 2) :2023/ ISO 7050 : 2011Cross Recessed Tapping Screws Part 2 Countersunk Flat Head
Cross Recessed ScrewsIS 18480 (Part 3) :2023/ ISO 7051 : 2011Cross Recessed Tapping Screw Part 3 Raised Countersunk Oval Head
Cross Recessed ScrewsIS 7483 : 2018/ ISO 7045 : 2011Pan Head Screws With Type H or Type Z Cross Recess – Product Grade A
Cross Recessed ScrewsIS 7485 (Part 1) : 2018/ ISO 7046-1 : 2011Countersunk Flat Head Screws (Common head Style) With Type H or Type Z Cross Recess - Product Grade A Part 1 Steel Screws of Property Class 4.8
Cross Recessed ScrewsIS 7485 (Part 2) : 2018/ ISO 7046-2 : 2011Countersunk flat head screws (common head style) with type H or Type Z Cross Recess - Product Grade A part 2 Steel Screws of Property Class 8.8, Stainless Steel Screws and Non - Ferrous Metal Screws
Cross Recessed ScrewsIS 7486 : 2018/ ISO 7047 : 2011Raised countersunk head screws (Common Head Style) with type H or type Z cross recess - Product grade A
Cross Recessed ScrewsIS 18507 : 2024Drywall Screws – Specification
Cross Recessed ScrewsIS 18508 : 2024Chipboard Screws – Specification
Cross Recessed ScrewsIS 18509 : 2023Cross-recessed Countersunk Head Wood Screws – Specification

Every notification on this order

DateNotificationStatusWhat it did
June 22, 2026S.O. 3298(E) PDF, 591 KB · GazetteAmendedIssued by the Ministry of Steel as the Cross Recessed Screws (Quality Control) Amendment Order, 2026, dated June 20, 2026 and in force on publication, it provides that enforcement of the entries at serial numbers 12, 13 and 14 of the 2025 order (drywall, chipboard and cross-recessed countersunk head wood screws) shall not be operative for a period of 3 years from date of publication in the gazette. Its preamble also refers to supersession of the 2025 order.
August 27, 2025S.O. 3927(E) PDF, 719 KB · GazetteIn forceIssued the Cross Recessed Screws (Quality Control) Order, 2025, dated and published August 27, 2025, in supersession of the 2024 order, with the same fourteen standards (the entries at serial numbers 1 to 4 marked 'revised as 18471: 2025') and exemptions, and with November 1, 2025 as the date of implementation in general, February 1, 2026 for small enterprises and May 1, 2026 for micro enterprises.
September 20, 2023S.O. 4099(E) PDF, 2.0 MB · GazetteIn forceIssued the Cross Recessed Screws (Quality Control) Order, 2024, dated September 17, 2024 and published in the Gazette of India on September 20, 2024, covering fourteen standards for cross recessed and other drilling, tapping, drywall, chipboard and wood screws, with dates of implementation six, nine and twelve months from publication for enterprises in general, small enterprises and micro enterprises.

Each notification is linked, as a PDF, in the list above.

Where a notification shows "Gazette", that links the Gazette of India's copy; ours was checked against it on October 20, 2026.